Cincinnati
TYPE 017 - Single Speed
TYPE 067 - Multi-Speed
SPEED LATHES

 
 
Type 017-222 Pedestal Mounted Speed Lathe
Type 017-222 with 4" 3-jaw chuck, pedestal base and foot switch.		 1/2 to 1 HP - Wide range of single and two speed models equipped with collet, taper nose or 4" 3-jaw chuck.
 
 
 
 

Cincinnati Speed Lathes are manufactured in three basic models to give extra quality, reliability and value at lower cost. Addition of optional equipment, such as pedestals, foot switches, air operated collets and chucks, special electrical equipment, extra speeds or special speed ranges, produces a unit "tailored" to your needs.
Type 017-203 Collet Speed Lathe
Type 017-203 with No. 5-C collet; operating handle on left side.
Type 067-251 Two Speed Lathe Grinder
Type 067-251 two speed unit; operating handle on right side (optional).

CONDENSED SPECIFICATIONS
Order by TYPE, SIZE and VOLTAGE

Style
HP
Speed
Type - Size
Collet Type
No. 5-C
1" diameter
capacity
1/2
Single Speed - any speed from 270 to 3600 RPM
017-201
3/4
Single Speed - any speed from 270 to 3600 RPM
017-202
1
Single Speed - any speed from 360 to 3600 RPM
017-203
1/2 - 1/4
Two Speed - 180 RPM minimum low; 2400 RPM maximum high
067-251
1 - 1/2
Two Speed - 270 RPM minimum low; 3600 RPM maximum high
067-252
Taper Nose
Type No. 2
Morse
1/2
Single Speed - any speed from 270 to 3600 RPM
017-211
3/4
Single Speed - any speed from 270 to 3600 RPM
017-212
1
Single Speed - any speed from 360 to 3600 RPM
017-213
1/2 - 1/4
Two Speed - 180 RPM minimum low; 2400 RPM maximum high
067-261
1 - 1/2
Two Speed - 270 RPM minimum low; 3600 RPM maximum high
067-262
Chuck Type
4" 3-Jaw
Chuck
1/2
Single Speed - any speed from 270 to 3600 RPM
017-221
3/4
Single Speed - any speed from 270 to 3600 RPM
017-222
1
Single Speed - any speed from 360 to 3600 RPM
017-223
1/2 - 1/4
Two Speed - 180 RPM minimum low; 2400 RPM maximum high
067-271
1 - 1/2
Two Speed - 270 RPM minimum low; 3600 RPM maximum high
067-272
Note: On two speed units, high speed must be double the low speed.
 

DIMENSIONS
For all standard Types

 
Spindle
Height
Height
Overall
Length
Width
Net
Weight
Bench Model
6
19
19
12
130
Pedestal Model
40
53
19
12
215
All dimensions are in inches, weight in pounds and are approximate.


Standard
  • Combination switch brake
  • Totally enclosed, non-ventilated motor
  • Type 067 - Drum switch for changing speed
  • No. 5-C collet, capacity to 1"; has 1" diameter hole through spindle; specify size of collet
  • OR
  • No. 2 internal Morse taper
  • OR
  • 4" 3-jaw chuck
  • Electrics: 3 phase, 60 Hertz, 230/460 volts (specify operating voltage when ordering)
  • OR
  • 3 phase, 60 Hertz, 230 or 460 volts on Type 067
 Optional at extra cost
  • Pedestal
  • Foot operated switch/brake
  • Other nose tapers, chucks and/or collets
  • Other electrics:  D, E, F, G 
  • Other staring equipment, including JIC standards
  • Expanding mandrels
  • Air operated chucks, collets and/or mandrels
  • Four speed drive
  • Other horsepowers and direct drive types

 

PREVIOUS PAGEINDEXEMAILRETURN TO HOME PAGE